Back in June I ran an oven building course at the Sustainability Centre in West Meon (nr Petersfield). Don Gribble was one of the attendees on that gloriously hot day. Don has now built his own oven and has shared his experience, and photos, for our benefit. There are some excellent words of advice, and some new approaches in his account so I advise you to read on.
Thanks for the sage words Don. Enjoy the oven!
Dear Simon, I was one of your students on the June course at West Meon. Now I’ve just completed an oven and we have had our first pizza party. From starting the construction to our first pizza party took just two weeks.
It wasn’t all plain sailing. I emptied out the sand too quickly and it all collapsed and I didn’t even curse (according to my wife).
I made the base from second-hand Celcon blocks and pallets. The largest pallet I could find was 1.0m x 1.2m so it needed the top layer of blocks to be extended over the sides. I put a wooden frame around the centre bricks and filled around them with concrete. This wooden frame was useful for nailing the roof and cladding to. The plinth finished up as 1.3m x 1.35m and I then built the oven according to your booklet instructions, viz. 80cm internal diameter by 40cm internal height.
For clay, I used powder clay, bought in 25kg bags from clayman-supplies.co.uk in Chichester. I chose a white clay known as Hyplas Ballclay This is about the cheapest clay available and costs just £11 a bag. My son and I mixed it one part powder to two parts builders sand. We found the easiest way was to mix it up dry by hand and then to puddle it with very little water added. For the outer layer another friend helped and he did the mixing with a shovel – once again hard work but easy to get the right firmness. For the insulation layer we mixed the powder clay with water until like thick batter (or yoghurt) and poured it on to wood shavings. We found that this did not hold together as balls which could be dropped, but it stuck well to the inner dome when just shoved on in handfulls.
You may be interested in the quantities since your booklet has some misleading advice [remember that Don used powdered clay here and I used wet clay in my book – SB]
- For the dome we used 10 25kg bags of builders sand.
- For the first layer, we used 4 bags of sand and 2 25kg bags of powder clay.
- For the arch and blendings we used half a bag of sand and a quarter of a bag of powder clay.
- For the insulation layer 7cm thick we used more than expected, namely, 2 bags of powder clay
- For the outer layer which we made only 5cm thick, we needed 5 bags of sand and 2 1/2 bags of powder clay.
As you can see from the photos, I prettied up the oven by nailing on palings and used these as support for a plastic sheet roof. There is a large 1.2m x 1.2m sheet of plywood under the centre of the plastic to stop it melting. The final photo shows that I have added a melamine/plywood working surface as a support for the aluminium peel. We plan to roll out our pizza dough direct on to the floured peel so that we can put it direct into the oven. We have a long BBQ fork to reach in and help pull the pizzas out on to the peel.
Our very first pizzas were decidedly crunchy because they picked up sand from between the bricks. Our second pizza party was really successful. We built a large softwood fire and pushed it to the back after about 1 1/2 hours. Then, before putting the pizzas in, we brushed the hearth quickly with a bristle brush to remove ash and sand.
There are, perhaps, one or two ideas which you might like to incorporate into a future edition of your booklet.
Arch and Chimney first
Incidentally, there is another thought which you might find useful. Because my first dome collapsed I was left with an arch and a pile of sand. The second time round, I built up the sand around the chimney to give a good shape to the smoke escape route. As a result, this oven breathes beautifully. I reckon that for everyone it would be best to build the arch first, then build the sand dome and the connections to the chimney, and only then put on the first layer of clay. This allows you to make a much better entry to the chimney – easier than reaching up inside through the arch.
I do hope you find this interesting. Thank you for starting me off with a wonderful course at West Meon.